SLM Solutions' Outfits Morf3D's State-of-the-Art Headquarters with Two SLM® 500s and the NXG XII 600 for its Applied Digital Manufacturing Center
Morf3D's 90,000 square foot ADMC facility will streamline and accelerate serial production lines across the globe.
How to Use Supports
Most entry-level 3D printers work by extruding material, and while this has lots of cost and safety advantages, it does come with some limitations. Creating a part with extreme overhangs, arches, or angles can be a challenge. Supports make printing these geometries possible.
SME Awards Recognize Additive Manufacturing Innovation, Skill and Leadership
Three Additive Manufacturing Community Awards presented at RAPID + TCT 2021
ASME Launches New Company to Accelerate Digital Transformation
Metrix, an ASME Company, will host in-person and virtual events, expert content, networking, and collaboration opportunities for the engineering community in a variety of industries
NEXA3D DELIVERS NEXT GENERATION INTERFACE LAYER TECHNOLOGY WITH THE IMMEDIATE COMMERCIALIZATION OF EVERLAST-2 MEMBRANE
• Advanced printing fidelity and membrane durability
• Enhanced Part Surface Quality and Smoothness
• Improved Part Detail and Definition
• Reduced Peel-Off Forces for Higher Speed printability
EnvisionTEC and Covestro Collaborate on Material and Printer Solutions for DLP 3D Printing Tooling Applications
New Resin e-PerFORM, Based on SLA Resin Somos PerFORM, Has Been Optimized for EnvisionTEC 3D Printers
Markforged Releases Eigerâ„¢ Fleet to Scale Additive Manufacturing
Eiger Fleet to Enable More Control and Automation of Distributed Manufacturing
To Overcome Capacity Constraints, Industry 4.0 Implementations Must Follow These 3 Steps
The benefits of industry 4.0 in manufacturing are clear, but unlocking them requires organizations to overcome capacity constraints. The keys are in these change management strategies.
AMFG Joins Stratasys GrabCAD® Software Partner Program
The users of Stratasys 3D printers and software can now seamlessly integrate with AMFG's Additive MES solutions
Stratasys Advances Shift to Additive Manufacturing at Scale
-New systems for the entire product value chain to be highlighted at the RAPID + TCT Conference
-New software partner and 3D printing materials help bring additive manufacturing to the factory floor
Kitov.ai Brings Advanced Automation Technology to Mexican Automotive Manufacturing
Kitov.ai will give a presentation on September 13 as part of a segment on manufacturing and automotive technologies.
WAI's Board of Directors cancels Interwire 2021
Industry 4.0 virtual conference set for October 26-27, 2021
Automatic Feed Announces New PRO Series Coil Feed Lines Developed to Address Versatile Needs of Tier Suppliers
Coil processing and pressroom automation expert Automatic Feed, known for its robust equipment for the automotive industry, has developed its PRO Series coil feed lines aimed at Tier automotive suppliers who are handling Ultra-High Strength Steels (UHSS), Advanced High Strength Steels (AHSS) and aluminum.
6 AI Driven Ideas to boost Asset Performance Management
Asset Performance Management software must evolve into knowledge hubs that not only deal with monitoring, but also gathering data from other dependent systems to provide much deeper insights and greater control.
EOS to Partner in Morf3D's Recently Announced Applied Digital Manufacturing Center
Morf3D's ADMC is a 90,000 square foot state-of-the-art facility harnessing applied research,
advanced engineering and application development, serial production and, most significantly,
new industry partnerships with global leaders to drive the industrialization of digital
manufacturing in high-growth markets.
Records 5536 to 5550 of 11778
First | Previous | Next | Last
Engineering - Featured Product
FLIR Si1-LD - Industrial Acoustic Imaging Camera for Compressed Air Leak Detection
The FLIR Si1-LD is an easy-to-use acoustic imaging camera for locating and quantifying pressurized leaks in compressed air systems. This lightweight, one-handed camera is designed to help maintenance, manufacturing, and engineering professionals identify air leaks faster than with traditional methods. Built with a carefully constructed array of MEMS microphones for high sensitivity, the Si1-LD produces a precise acoustic image that visually displays ultrasonic information, even in loud, industrial environments. The acoustic image is overlaid in real time on a digital image, allowing you to accurately pinpoint the source of the sound, with onboard analytics which quantify the losses being incurred. The Si1-LD features a plugin that enables you to import acoustic images to FLIR Thermal Studio suite for offline editing, analysis, and advanced report creation. Field analysis and reporting can also be done using the FLIR Acoustic Camera Viewer cloud service. Transferring of images can be managed via memory stick or USB data cable. Through a regular maintenance routine, the FLIR Si1-LD can help facilities reduce their environmental impact and save money on utility bills.
